Off Roading Forums banner
1 - 20 of 20 Posts

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #5 ·
Re: Pic of my flat dash going in my YJ

Just the floor vent. I have a 3-way switch Low Off High.
 

·
Registered
Joined
·
2,348 Posts
Re: Pic of my flat dash going in my YJ

Looks great, do you have any close up photos of it? I like the configuration you went with.
Be sure to post up a few snap shots once you have it installed.

I have all the pieces for my flat dash conversion.. I have just not quite decided how I am going to lay it out yet..

Nice work.
 

·
Registered
Joined
·
1,445 Posts
Re: Pic of my flat dash going in my YJ

Looks really good, great fab work. I also like the configuration, everything looks well proportioned to the dash.
 

·
Registered
Joined
·
668 Posts
Re: Pic of my flat dash going in my YJ

ya the dash is nice... but i dont see the jeep running /ubbthreads/images/graemlins/cussing.gif stop taking your time you can do that later /ubbthreads/images/graemlins/neener.gif
 

·
Registered
Joined
·
1,806 Posts
Re: Pic of my flat dash going in my YJ

Very Nice /ubbthreads/images/graemlins/applause.gif
 

·
Registered
Joined
·
630 Posts
Re: Pic of my flat dash going in my YJ

looks good tobad there is a none runing jeep in the background
 

·
Registered
Joined
·
13,432 Posts
Re: Pic of my flat dash going in my YJ

'Cept for the guy holding it... /ubbthreads/images/graemlins/crazy.gif

It looks great!
 

·
Registered
Joined
·
484 Posts
Re: Pic of my flat dash going in my YJ

im jealous!!! /ubbthreads/images/graemlins/40BEER.gif /ubbthreads/images/graemlins/thumbsup.giflooks great mach /ubbthreads/images/graemlins/yourock.gif

hey how low do you air down to get that thing out the door anyways?
 

·
Registered
Joined
·
630 Posts
Re: Pic of my flat dash going in my YJ

he does not need to he misses by like an inch
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #14 ·
Re: Pic of my flat dash going in my YJ

No it needs to be down. like 1 psi. The side walls would hold it up to much at my old house. was a pain. But here its good. plus with the Skid and the driveshafts and stuff it should fit just fine.
 

·
Registered
Joined
·
156 Posts
Re: Pic of my flat dash going in my YJ

The dash looks good! Did you make your cage from scratch, or was that a kit that was purchased and then welded inplace?
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #16 ·
Re: Pic of my flat dash going in my YJ

No its a M.O.R.E kit. and its bolt in. Did not want the weld in kit. that way i can take it out if i ever needed to.
 

·
Registered
Joined
·
946 Posts
Re: Pic of my flat dash going in my YJ

You using gold plated pins in those Molex connectors? I think I might be able to send you some if you want to use some. They would never corrode on you like the nickle ones will.
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #18 ·
Re: Pic of my flat dash going in my YJ

No. But thats ok. Im going to use dielectric grease or anti oxidizing jel. Should work good..

But thanks. /ubbthreads/images/graemlins/smile.gif
 

·
Registered
Joined
·
546 Posts
Looks great Mach. While looking at your pics I was checking out your steering, where did you get your pitman arm? How long is it? Aaron
 
1 - 20 of 20 Posts
Top